Power Management ICs PMIC IC

Linear Voltage Regulator, Fixed, 7.5V to 20V input, 5V/3A out, TO-3-3

MOSFET Driver, Low Side, 4.5V-18V supply, 1.5A and 7 ohm output, DIP-8This listing is for Pack of 56.

Gate Driver, 2 Channels, Half Bridge, SiC MOSFET, Module, Inverting This listing is for Each.

Gate Driver, 2 Channels, High Side and Low Side, MOSFET, ModuleThis listing is for Each.

LINEAR VOLT REG, 5V, 0.1A, SOT-89-3 ROHS COMPLIANT: YES (moq 5)This listing is for Pack of 5.

DC/DC CONV, BUCK/BOOST/INV, 100KHZ, SOIC WARNING: Cancer and Reproductive Harm - . This listing is for Each.

Product Overview The MAX6126BASA30+ is a high precision, ultra low noise, low dropout, series voltage reference in 8 pin NSOIC package. This voltage reference features curvature correction circuitry, high stability and laser trimmed thin film resistors that result in 2ppm/°C temperature coefficients and an excellent ±0.06% (maximum) initial accuracy. The low noise reference architecture produces a low flicker noise of 1.3µVP-P and wideband noise as low as 60nV/√Hz without...

IC, FET DRIVER 9A, 4421, DIP8This listing is for Each.

LM185H-1.2/NOPB . - MICROPOWER VOLTAGE REF DIODE, 125DEG C

MCP111-475E/TO - Voltage Detector, 1V-5.5V supply, 4.625V Threshold, 100 µs Delay, Active-Low, Open-Drain, TO-92-3This listing is for Each.

Product Overview The MAX6030AEUR+T is a precision, low power, low dropout voltage reference in 3 pin SOT-23 package. It features curvature correction circuit and laser trimmed thin-film resistors that result in a low temperature coefficient of 6ppm/°C and initial accuracy of better than 0.2%. This series mode voltage reference draws only 27μA of quiescent supply current and can sink or source up to 500μA of load current. The device offers a supply current that is virtually independent...

Product Overview The MAX701EPA+ is a power supply monitor with reset in 8 pin DIP package. This supervisory circuit is used to monitor power supplies in microprocessor (µP) and digital systems. The RESET/complimentary RESET output of the MAX701EPA+ has to be in the correct state for VCC voltages down to +1V. It provides excellent circuit reliability and low cost by eliminating external components and adjustments when used with +5V powered circuits. The primary function of device is to provide...

NCP803SN293D3T1G - Microprocessor Reset Monitor, Open-Drain, 1.2V to 5.5V Supply, 2.93 V Threshold, 330 ms, SOT-23-3 WARNING: Cancer and Reproductive Harm - .

VOLT REG, FIXED, -5V, 0, 1A, 0 - 125DEG C ROHS COMPLIANT: YES (moq 5) WARNING: Cancer and Reproductive Harm - .This listing is for Pack of 5.

V REG, 1.7VDO, 0.1A, 12V, 5%, 8SOIC (moq 2500) This listing is for Pack of 2500.

Product Overview The LM4040DIM3-10.0/NOPB is a Precision Micropower Shunt Voltage Reference, the advanced design of the voltage reference eliminates the need for an external stabilizing capacitor while ensuring stability with any capacitive load, thus making the LM4040 series easy to use. Further reducing design effort is the availability of several fixed reverse breakdown voltage 10V. The voltage reference uses a fuse and Zener-zap reverse breakdown voltage trim during wafer sort to ensure that...

Product Overview The MAX6384XS31D3+T is a single low voltage, low power microprocessor (μP) reset circuit in 4 pin SC-70 package. This microprocessor (μP) supervisory circuit monitors power supply voltage ranging from +1.8V to +5V while consuming only 3μA of supply current at +1.8V. Whenever VCC falls below the factory-set reset thresholds, the reset output asserts and remains asserted for a minimum reset timeout period after VCC rises above the reset threshold. It has a push-pull active-low...

Product Overview The TNY266PN integrates a 700V power MOSFET, oscillator, high voltage switched current source, current limit and thermal shutdown circuitry onto a monolithic device. The start up and operating power are derived directly from the voltage on the DRAIN pin, eliminating the need for a bias winding and associated circuitry. In addition, the TNY266PN incorporates auto-restart, line undervoltage sense, and frequency jittering. An innovative design minimises audio frequency components in...

Product Overview The TOP221PN is a 9W second generation 3-terminal Off-Line PWM Switch provides several enhancements over the first generation TOPSwitch family. Many significant circuit enhancements that reduce the sensitivity to board layout and line transients now make the design even easier. TOPSwitch incorporates all functions necessary for a switched mode control system into a three terminal monolithic IC are power MOSFET, PWM controller, high voltage start up circuit, loop compensation and...

VN5E160STR-E - Power Load Distribution Switch, High Side, 13 V Input, 10 A, 0.16 ohm, 1 Output, SOIC-8This listing is for Each.

VNL5300S5TR-E - Power Load Distribution Switch, Low Side, 5 V Input, 2.8 A, 0.3 ohm, 1 Output, SOIC-8This listing is for Each.

DRIVER, MOSFET, DUAL, HIGH SPEED This listing is for Each.

MCP1501-20E/SN - VOLT REF, SERIES, 2.048V, -40 TO 125DEGC WARNING: Cancer and Reproductive Harm - . This listing is for Each.

Product Overview The MAX6008BEUR+T is an ultra-low power precision shunt voltage reference in 3 pin SOT-23 package. This two terminal shunt band gap voltage reference is ideal for space critical and low power applications. The on-chip thin film resistors are laser trimmed to provide initial accuracy of 0.5% and low temperature coefficients of ±75ppm/°C. This device can be used as low power and high precision upgrade to ICL8069, LM385, LT1004 and LM4040 references. It is used in battery...

Product Overview The MAX6102EUR+T is a low cost, low dropout, micropower voltage reference in 3 pin SOT-23 package. This three terminal device features a curvature correction circuit and laser trimmed, thin film resistors that result in a temperature coefficient of ±75ppm/°C and an initial accuracy of 0.4%. This series mode voltage reference draw only 90μA of supply current and can source 5mA and sink 2mA of load current. It offers a supply current that is virtually independent of...

Product Overview The MAX6314US26D3+T is a 68HC11/bidirectional compatible microprocessor (μP) reset circuit in 4 pin SOT-143 package. This low power CMOS supervisory circuit is designed to monitor power supplies in μP and digital systems. The complementary RESET output of MAX6314 is bidirectional, allowing it to be directly connected to μPs with bidirectional reset inputs such as 68HC11. The MAX6314 also provides a debounced manual reset input. This device performs a single function that...

MAX6012AEUR+T - VOLTAGE REF, SERIES, 1.247V, SOT-23-3 This listing is for Each.

MOSFET DRIVER, -40 TO 125DEG CThis listing is for Each.

LINEAR VOLT REG, 0.02A, 440V, TO-243AA-3 WARNING: Cancer and Reproductive Harm - .This listing is for Each.

IC, GATE DRIVER, HV, 3PHASE, 28SOIC

MOSFET DRIVER, -40 TO 125DEG CThis listing is for Pack of 5.

LM4041CYM3-1.2-TR - VOLTAGE REF, SHUNT, 1.225V, SOT-23-3This listing is for Each.

LINEAR VOLT REGU, FIXED, 12V/0.5A, TO220 ROHS COMPLIANT: YESThis listing is for Each.

Product Overview The MAX6375XR29+T from Maxim Integrated Products is an ultra-low-power voltage detector in 3 pin SC-70 package. It is an ultra-low-power circuit used for monitoring battery, power supply and regulated system voltages. Each detector contains a precision bandgap reference, comparator and internally trimmed resistors that set specified trip threshold voltages. It provides excellent circuit reliability and low cost by eliminating external components and adjustments when monitoring nominal...

NCP431BVSNT1G - Voltage Reference Shunt - Adjustable, 2.5V to 36V Ref, 50ppm/°C, SOT-23-3 WARNING: Cancer and Reproductive Harm - . This listing is for Pack of 3000.

DC-DC CONV, BUCK, 52KHZ, TO-220-5 This listing is for Each.

IC, PWM INVERTING SWITCHING REG, SOT23-5 WARNING: Cancer and Reproductive Harm - .This listing is for Each.

Product Overview The LM285 series micropower band-gap Voltage Regulator Diode designed to operate over a wide current range of 10μA to 20mA, this device feature exceptionally low dynamic impedance, low noise and stable operation over time and temperature. Tight voltage tolerances are achieved by on-chip trimming. The large dynamic operating range enables these devices to be used in applications with widely varying supplies with excellent regulation. Extremely low operating current make this device...

V REG, 2VDO, 1A, 5V, 3TO220 WARNING: Cancer and Reproductive Harm - .This listing is for Each.

IC, VOLTAGE REG WARNING: Cancer and Reproductive Harm - .This listing is for Each.

MAX1232EPA+ - MPU Supervisor Circuit, Active-High/Low, 4.5V to 5.5V, 4.37V Threshold, 610 ms Delay, DIP-8 This listing is for Each.

MAX6610AUT+T - Voltage Reference, Series, 2.56V Ref, ± 10ppm/°C, SOT-23-6 This listing is for Each.

Product Overview The MAX6643LBBAEE+T from Maxim Integrated Products is an automatic PWM fan-speed controller with overtemperature output in 16 pin QSOP package. It monitors temperature and automatically adjusts fan speed to ensure optimum cooling while minimizing acoustic noise from the fan. Each device measures two temperature locations. It monitors temperature and adjust the duty cycle of the PWM output waveform to control the fan’s speed according to the cooling needs of the system. The...

STBC08PMR - Battery Charger, 1 Cell Li-Ion Battery, 6.5V Input, 4.2V/0.8A Charge, DFN-6This listing is for Each.

MOSFET Driver Dual, Low Side Non-Inverting, 4.5V-18V supply, 3A peak out, 3.5 Ohm output, DIP-8This listing is for Each.

TNY274PG - AC/DC CONV, FLYBACK, -40 TO 150DEG CThis listing is for Each.

MAX691CWE+ - Supervisory Circuit, Active-Low Reset, 4.75V to 5.5V, SOIC-16This listing is for Each.

MAX810STRG. - Very Low Supply Current Microprocessor Reset Monitor, Active-High, 1.2V to 5.5V, SOT-23-3 (moq 3000)

Product Overview The MAX811TEUS+T is a 4-pin Voltage Monitor with manual reset input. The MAX811 is low-power microprocessor (μP) supervisory circuit used to monitor power supplies in μP and digital systems. They provide excellent circuit reliability and low cost by eliminating external components and adjustments when used with 5V-powered or 3V-powered circuits. The MAX811 also provide a debounced manual reset input. These devices perform a single functions of they assert a reset signal whenever...

VN5016AJTR-E - Power Load Distribution Switch, High Side, 13 V Input, 65 A, 0.016 ohm, 1 Output, PowerSSO-12 WARNING: Cancer and Reproductive Harm - .This listing is for Each.

AP22811AW5-7 - POWER LOAD SW, HIGH SIDE, -40 TO 85DEG CThis listing is for Pack of 5.

BTS70102EPAXUMA1 - POWER LOAD SW, AEC-Q100, 28V, TSSOP-14 WARNING: Cancer and Reproductive Harm - .This listing is for Each.

Product Overview The ISL60002 FGA series very high precision analog Voltage Reference fabricated in Intersil's proprietary Floating Gate Analog (FGA™) technology and feature low supply voltage operation at ultra-low 350nA operating current. Additionally, the ISL60002 family features guaranteed initial accuracy as low as ±1mV and 20ppm/°C temperature coefficient. The initial accuracy and temperature stability performance of the ISL60002 family, plus the low supply voltage and 350nA...

ISL6292-2CR5Z-T - Battery Charger for 1 Cell of Li-Ion, Li-Pol battery, 6.5V input, 1.1 A charge, QFN-16

ISL88001IE29Z-TK - MPU Supervisor, 1.8V-5.5V supply, 2.92V threshold/200 ms delay, Active-Low, Push-Pull, SC-70-3 (moq 2000)

ISL88002IH23Z-TK - Microprocessor-MPU Supervisor, 1.8V-5.5V supply, 2.32V threshold/200 ms delay, Open-Drain, SOT-23-3 (moq 2000)

MAX6070BAUT33+T - VOLT REF, SERIES, 3.3V, -40 TO 125DEG C This listing is for Each.

MIC2075-1YMM - Power Distribution Switch, Current Limit, Active High, 1 Output, 0.09 ohm On, 5.5 V, 0.7 A, MSOP-8 (moq 900)

Product Overview The MIC2076-1YM is a dual-channel power Distribution Switch optimized for general-purpose power distribution requiring circuit protection. The switch is internally current limited and has thermal shutdown that protects the device and load. The switch offers smart thermal shutdown that reduces current consumption in fault modes. When a thermal shutdown fault occurs, the output is latched off until the faulty load is removed. Removing the load or toggling the enable input will reset...

Product Overview The DS1811-5+T&R is a 5V EconoReset monitor with open drain output in 3 pin TO-92 package. A precision temperature compensated reference and comparator circuit is used to monitor the status of the power supply (VCC). It provides a function of detecting out of tolerance power supply conditions and warning a processor based system of impending power failure. When VCC is detected in out of tolerance condition, an internal power fail signal is generated which forces reset to the active...

Product Overview The MAX6035AAUR50+T is a high supply voltage, precision micropower voltage reference in 3 pin SOT-23 package. This three terminal device is available with output voltage of 5V. It is an excellent upgrade for industry standard device such as the REF02 and REF43. The device offers 14x lower power than the REF02 and 5x lower power than the REF43. It features a proprietary temperature coefficient curvature correction circuit and laser trimmed thin film resistors that result in a low...

Product Overview The MAX6365PKA31+T is a low power µP supervisory circuit with battery backup and chip enable gating in 8 pin SOT-23 package. This supervisory circuit simplify power supply monitoring, battery backup control functions and memory write protection in microprocessor (µP) systems. This device performs four basic system functions such as providing a µP reset output during VCC supply power-up, power-down and brownout conditions, memory write protection through internal...

Product Overview The MAX6748KA+T is a low power microprocessor (μP) reset circuit with capacitor adjustable reset and watchdog timeout delay in 8 pin SOT-23 package. This microprocessor (μP) supervisory circuit monitors single/dual system supply voltages from 1.575V to 5V and provides maximum adjustability for reset and watchdog functions. The MAX6748 asserts a reset signal whenever the VCC supply voltage or RESET IN falls below its reset threshold or when manual reset is pulled low. The reset...

Product Overview The REF01CESA+ is a precision voltage reference in 8 pin NSOIC package. This industry standard voltage reference has single supply operation over an input voltage range of 13V to 33V. The stable 10V output of this device can be adjusted over a ±6% range with minimal effect on temperature stability. The REF01C offers low current drain of 1mA. This device is used in analogue to digital converters, digital to analogue converters, digital voltmeters, voltage regulators and threshold...